Supports most stock washer and wiper switches/configurations. Steering column connectors can plug directly into most aftermarket steering columns or stock 71-74 Mopar columns using the adapter and terminals included in the kit. Separate under dash courtesy lamp assemblies are also included for use along with your original dome/interior lighting feeds.
Instrument cluster wiring is designed with a cluster harness disconnect system for easy service and assembly. Original style terminals, lamp sockets, connectors, and locking nuts or factory printed circuit board connector that will attach to the original cluster (another American Autowire exclusive) are provided for all stock cluster connections. The system will also connect into most popular aftermarket gauges such as CLASSIC INSTRUMENTS, DAKOTA DIGITAL, AUTOMETER, VDO, and others. Rear body harness assembly plugs into the main harness in the stock location, and will connect into your stock rear tail lamp assembly harness at the back of the car. Our longer leads allow for stock or custom routing of the wires.
Rear body wiring includes backup light lead wires, stop and tail light lead wires, dome light leads, terminals, connectors and lamp sockets, new side marker lamp assemblies, and fuel tank sender wire with trunk grommet and tank connection. New floor dimmer switch is provided for ease of installation. Wire length and connection accommodate original floor mount dimmer switch.New headlight switch is included. GM bulkhead connectors for the engine and front light wiring are included (another American Autowire exclusive), and allow for easy installation with original or custom routing. Engine wiring includes connectors for original points type distributors, OEM Chrysler style starter relay connections, tach and ignition leads, etc. High-powered 1-wire alternator connections are supplied.
Front lighting includes extra-long leads that can be routed for stock or custom applications. All head light, parking light, and directional light leads, along with a switched trigger wire for an electric fan relay (usually recommended with AC) are provided. Mating terminals and connectors are also provided for you to complete your custom installation. Many original style light sockets, switch body connectors, terminals, etc. This kit WILL NOT support the use of a factory ammeter.
All AAW kits are engineered to supply the optimum charge to the battery. To achieve this performance, we route our 8ga.Charge wire directly from the alternator output charge terminal to the starter battery terminal. Due to the path of the charge being altered from the stock configuration, the gauge can no longer see a charge vs.
A discharge, so it will not work properly. When ammeters were originally used, most generator or alternator current outputs were rated at a maximum of about 25-60 amps. Modified cars being built today typically utilize a 100 amp or higher output alternator. With these higher current units, ammeters, generally speaking, become a safety hazard. Ammeters are usually wired in parallel to the charging circuit, are typically un-fused, and can short very easily causing a fire.
A voltmeter is recommended as a good alternative. This kit IS NOT set up with a resistance wire for a standard, points type ignition system. It is wired with a full 12 volt primary ignition feed that is hot in the run position. Primary ignition voltage in the starting position is handled via a full 12 volt bypass wire.
Our system will support HEI, MSD, other electronic ignition systems, as well as most all computerized Fuel Injection systems. If you wish to run a points type system, there are illustrations on the engine connection pages to do so. Extra parts (ballist resistor) that are not included in this kit will be required to complete that operation.
The early Mopar generators and externally regulated alternators are just not up to the task of providing power to an expanded wiring system like these classic update kits. The point of this kind of kit is really to allow people a way to upgrade and expand their wiring system and so an alternator upgrade is usually part and parcel to this kind of upgrade. NOTE: These kits are recommended for MODIFIED original vehicles, not OEM restoration projects. Note: This wiring is designed to work on Internally regulated alternator and have a 12v feed for the coil/distributor/ignition box. It is wired with a full 12 volt primary ignition feed that is hot in both the start and run positions.It will support HEI, MSD, other electronic ignition systems, as well as computerized Fuel Injec- tion systems. Extra parts that are not included in this kit will be required to complete that operation.
Thank you for shopping at Matts Classic Bowties. The item "American AutoWire 71-74 Mopar B Body Wiring Harness 510691" is in sale since Monday, May 14, 2018. This item is in the category "eBay Motors\Parts & Accessories\Vintage Car & Truck Parts\Other Parts". The seller is "mattsclassicbowties" and is located in Bellmawr, New Jersey.
This item can be shipped to United States, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, South Korea, Indonesia, Taiwan, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Bahamas, Israel, Mexico, New Zealand, Singapore, Switzerland, Norway, Saudi arabia, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Brazil, Chile, Costa rica, Panama, Trinidad and tobago, Guatemala, Honduras, Jamaica, Bangladesh, Brunei darussalam, Bolivia, Ecuador, Egypt, French guiana, Guernsey, Gibraltar, Guadeloupe, Iceland, Jersey, Jordan, Cambodia, Liechtenstein, Luxembourg, Monaco, Macao, Martinique, Nicaragua, Peru, Pakistan, Paraguay, Viet nam, Uruguay, Canada.